Mileage Correction

BMW X5 FEM Odometer Correction: Cheapest & Easiest Way

Purpose: To do Mileage Correction

The car: 2014-2015 BMW X5 F15


Have tested most odometer correction tools popular in the market..

Some success and some failure

Here are the test result and suggestion. Hope it helps you out.

Digiprog 3: NO

Digiprog 3 v4.94 will not do bmw f15. Digiprog can not erase original eeprom

Eeprom: NO

You don’t need to buy eeprom (eraser can erase these eprom ) only can filter and install in dashboard or FEM and Avdi, BMW explorer or …….

Vvdi prog: YES

If it is cas4 you need to do cas and dash with vvdi prog

CAN filter: YES
If it is with fem you can use can filter and have also to do dash
R270: YES
You can use vvdi prog or r270

E-sys: YES

It can be cleared in custom kombi coding with esys

Cheapest way:

Program new EEPROM with Xprog, filter in Fem will be cheapest

Eraser is about $110

Easiest way:

X5 has fem
Can filter in dash is easiest.
Remove battery First

Btw, i think not possible change it in new type of key f15 without change to new key.

buy new bdc, then key will take km from there

You’d better read –

buy new FEM ( 490eu) , buy New Ecu if it diesel ( doesn’t matter which engine) , program the dash on new KM

update the car with ISTA ( latest version—- if you have) and car will get 100% new KM in all ECU

but if it diesel , then Buy New Engine Ecu also

but be careful because all Ecu and Fem come out from fabrik in latest version of ISTA , which can not be LOW DOWN with another tools,

if you have ISTA online , then can not be problem at all !!!

I know the guy who have ISTA online with own server , and never get problem ….ISTA online is cost for 1 year 1800 eu .

(Solved) Digimaster 3 cannot connect to the server when updating software

Digimaster 3 error: cannot connect to the server

Solution: you should connect the LAN cable, then Management – Remote assistance – Set IP

Steps to update Digimaster 3:

Step 1: plug the power supply to digimaster3 and insert the network cable into the LAN port on the digimaster3 unit.

Step 2: select “Management”

Step 3: select “Update”

Step 4: select “Software Upgrade”

Step 5: the machine is upgrading

V2019 Super DSP3 Odometer Correction Vehicle List

Comparing v2017 Super DSP3 mileage programmer, the newest V2019 Super DSP III adds newer vehicles, including Audi/VW/Skoda/SEAT MQB platform and Benz/Land Rover/Jaguar/Volvo/Porsche 2010-2017 models.

2019 Super DSP3+ Mileage Correction Tool Car List:
2019 Super DSP3+ Odometer Correction Car List

VAG MQB Platform odometer reset vehicle list:

vw/golf sportsvan 06.2014- nec35xx diag    by obd2

vw/golf mk7 06.2014- nec35xx diag    by obd2

vw/passat b8 06.2014- nec35xx diag     by obd2

vw/polo 06.2014- nec35xx diag    by obd2

vw/tiguan 06.2014- nec35xx diag by obd2

vw/touran 06.2014- nec35xx diag by obd2

audi/a3 06.2014- nec35xx diag     by obd2

audi/q2 06.2014- nec35xx diag     by obd2

skoda/fabia 06.2014- nec35xx diag by obd2

skoda/rapid 06.2014- nec35xx diag      by obd2

skoda/octavia 06.2014- nec35xx diag    by obd2

skoda/superb 06.2014- nec35xx diag    by obd2

seat/ibiza 06.2014- nec35xx diag   by obd2

seat/toledo 06.2014- nec35xx diag by obd2

seat/leon 06.2014- nec35xx diag   by obd2

*attention:the above new updates are for car models with platform mqbab-(continental/vdo) from 6/2014

OBDSTAR X300 DP plus VS X300 DP VS Lonsdor k518ise

Post topic: OBDSTAR X300 DP PLUS VS X300 DP VS Lonsdor K518ISE in the software functions, vehicle coverage, features, hardware etc. And followed with obdstar X300 DP plus A package Vs B package Vs C package. Finally ends with obdstar X300 DP plus features & real pictures.

Part 1: obdstar X300 DP plus VS X300 DP VS Lonsdor k518ise


Part 2: obdstar X300 DP plus obdstar X300 DP plus A package Vs B package Vs C package


Part 3: obdstar X300 DP plus features & real pictures.

Hardware Advantages:

1.  Built-in VCI box
2.  8-inch touch screen


3.  Chargedirectly via OBD interface
4.  Practical and high-end gift box
5.  Industrial design with silicone case
6.  Back bracket design:prop on the steering wheel or stand on the table
7.  With 4 Toyota simulation keys (the fifth is coming soon)


Simulated key 1 applies to the vehicle with 94/D4 type of smart key;
Simulated key 2 applies to the vehicle with 98 type of smart key;
Simulated key 3 applies to the vehicle with 88/A8 type of smart key;
Simulated key 4 applies to the vehicle with A9 type of smart key;

8.  P001 programmer: EEPROM adapter + RFID adapter+ Key Renew adapter


9.  Add the clip of reading SOP 8PIN EEPROM


10. C001/C002 circuit board to read and write chip data with weldingC001 circuit board


Image 1: C001 circuit board is compatible with old NO. 3 and 4 circuit boards, applying to EEPROM chip dismantling and reading, Tianjin FAW and VIZHI immobilizer coil initialization and other functions.C001 circuit board


Image 2: C002 circuit board is connected by W001, W002 or W003 without welding the chip.

11. IMMO induction coil to detect the key induction coil failure of the vehicle.


12. Add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)


ECU Programming/Cloning

ECU cloning means copy ECU, that is the OBDSTAR X300 DP Plus copies the data from the original car ECU, then write it into another same ECU hardware, so that it can achieve the same function as the original ECU.

When you want to change the new ECU or the second ECU, if you use X300 DP Plus to clone via OBD, you won’t need to go to the 4s store to do the online programming or dismantle ECU to weld, read & write.

ECU clone Pros :

No need to go to 4S shop, convenient, fast and save money.

Simplify the operating steps, even the amateur can also operate.

No need to dismantle and weld the ECU to read & write, it is zero risk to clone ECU via OBD with the X300 DP Plus.

Switch activation function

Nowadays, many car models’ accessory power supply of the dashboard or audio equipment needs to be activated to enter the boot status through the related module CAN.

However, when the car technician maintains the dashboard / audio equipment, the main unit is out of the CANBUS network so it maybe won’t boot.  OBDSTAR Scanner X300 DP plus” switch activation function” can emulate the CANBUS communication to active the power supply of dashboard / Audio so that it can enter the boot status, then it will test and verify the dashboard and the Audio, also the technician can save money avoiding to purchase many the boot platform and cables of kinds of car models

13. Adds the “Help” functionincluding the testable car models, update notice, special features, help instruction, wiring diagram etc.

Testable car models: The user can read the testable car models and year.

Update notice: The user can read all of the update content.

Features: The user can read all of the special features and the functions that only X300 DP Plus supports.

Help instruction: Built-in the guide and instruction for each car model or function.

Wiring diagram: Built-in ECU wiring diagram, more intuitive and convenient.

Pictures mean a lot:


obdstar DP plus accessories:


obdstar X300 dp plus accessories

OBDSTAR X300 DP Plus On Package:

7-13 7-14 7-15 7-16 7-17

No Comments in Mileage Correction

DSP III DSP3 Odometer Correction Tool



Super DSPIII Odometer Correction Tool Super DSP3 Mileage Programmer fully supports newest high-end Car

DSP III work for AUDI/VW/ SKODA/SEAT/BENTLE/MERCEDES/ JLR/ VOLVO/ PORSCHE 2010-2017 years of models Mileage Programming via OBD adapters.

super dspiii on is the most complete programming device for digital odometers,  It is a high-quality embeded system, which offers a maximum of flexibility and working comfort.

Technical reference:

1.Powered by industrial grade core board with Freescale i.MX28x processor, speeds up to 650MHZ, 800*480 TFT LCD and touch screen(7.0″.16:9). Convenient keyset. USB host and USB device. SD card interface. 128MB NandFlash, 128MB DDRII.

2.We use industrial grade components to ensure the stability and reliability under a wide temperature range, from -40℃ to +85℃.

3.Whole machine passed EMC industry 4 grade quality assurance and durable performance, the product stability greatly improved.

4.The Wince6.0 operating system can ensure the software platform reliability and compatibility.

5.Self-check function integrated in system.

Enhanced OBD functions, including CAN-BUS / J1850 / CCD-BUS / ISO9141 / SPI protocols.

6.Intuitive operability by full menu and picture guidance. All data can be edited, stored and loaded.

7.Color connection picture is on the screen whenever you need.

The stored data can be transferred to a PC by USB port or SD card, and also can be transfer to wherever you want directly by internet.


17-1 17-2 17-3 17-4 17-5 17-6 17-7 17-8