autotool.biz

Month: August 2019

Diagnostic Codes on Caterpillar ET Software

Diagnostic Capabilities

Diagnostic Codes
The engine’s Electronic Control Module (ECM) has the ability to monitor the circuitry between the ECM and the engine’s components. The ECM also has the ability to monitor the engine’s operating conditions. If the ECM detects a problem, a code is generated.

Diagnostic-Codes-on-Caterpillar-ET-Software

There are three categories of codes:
-Diagnostic Code
-Event Code
-Flash Code

-Diagnostic Code – A diagnostic code indicates an electrical problem such as a short or an open in the engine’s wiring or in an electrical component.
-Event Code – An event code is generated by the detection of an abnormal engine operating condition. For example, an event code will be generated if the oil pressure is too low. In this case, the event code indicates the symptom of a problem. Event codes indicate mechanical problems rather than electrical problems.
-Flash Code – Diagnostics and events are reported via flash codes. When a diagnostic code or an event code becomes active, the specific condition is immediately reported to the operator through a series of flashes on the diagnostic lamp. By counting the flashes, a numeric representation of the diagnostic code or event code is revealed.

CAT Caterpillar ET Codes can have two different states:
-Active
-Logged
-Active Codes
An active code indicates that a problem is present. Service the active code first. For the appropriate
troubleshooting procedure for a particular code, refer to the following troubleshooting procedure:
a. Troubleshooting, “Diagnostic Trouble Codes”
b. Troubleshooting, “Event Codes”
Refer to the Troubleshooting, “Diagnostic Code Cross Reference” for information that relates to converting flash codes to the equivalent diagnostic code or to the equivalent event code.

-Logged Codes
The codes are logged and stored in the ECM memory. The problem may have been repaired and/or the problem may no longer exist. If the system is powered, it is possible to generate an active diagnostic code whenever a component is disconnected. If the component is reconnected, the code is no longer active but the code may become logged.
Logged codes may not indicate that a repair is needed. The problem may have been temporary. Logged codes may be useful to help troubleshoot intermittent problems. Logged codes can also be used to review the performance of the engine and of the electronic system.

No Comments in Auto key Programmer

SEC-E9 Key Cutting Beginner Guide for Toyota Camry TOY43

SEC-E9 Key Cutting Machine is a powerful key cutting machine, including dimple keys, tubular keys, single standard keys and motorcycle keys.Here CnAutotool.com show you this useful instruction for how to use SEC-E9 to cut key for Toyota Camry TOY43 key.

Two Ways to Enter Key Data of Toyota TOY43 Keys

Method 1:Vehicle Selection

Power on SEC-E9 key cutting machine and click [Automobile]–>[Toyota]–>[Camry]–>[2006-10]
SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-1 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-2 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-3 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-4

Method 2:Key Blank Number

Click [Search] button,input “TOY43” and select [Silca]–>[TOY43 (903) 10]

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-5

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-6

Three ways to get key numbers of Toyota TOY43 Keys

First Way 1:Decoding Original Key

Press [Decodes] button to enter decoding page,and select blue icon as sense key location at right bar.

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-7 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-8

Fix the original key on top level of the clamp please pay attention to the key position

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-9

Press [Decode] button to start decoding original key and get the key numbers

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-10

Then SEC-E9 key cutter will start decode

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-11

Second Way:Search Key Code

This is key code:63089 for a Toyota Camry Key

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-12

Click [Code] button and input “63089” to get the key numbers

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-14

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-15SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-16
SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-17

Third Ways to Input Key Numbers Directly

Click “Input” button and input the key numbers you get from other ways,such as cylinder,lishi tool,or instacode etc.

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-18 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-19 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-20 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-18 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-19

Cut a New Toyota Camry Key

Press [Cut] button to enter cutting page
SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-20

Press [Cut] button to enter cutting page

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-21

Select [nkl-silver] as speed and the most right blue icon as sense key location

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-22

Fix a new key blank at the top level of the clamp,please pay attention to the key position

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-24

Press [Cut] button to start cutting a new key please remember to close the safe gate

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-25

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-26

Cutting proceed…

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-27 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-28 SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-29

Cutting done,oopen the safe gate clean the clamp,then take out the new key

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-30
SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-31

Test new key,work well

SEC-E9-Key-Cutting-Machine-Cut-Toyota-TOY43-Key-32

No Comments in Uncategorized

How to ICOM Next DHCP Configuration + WiFi Connection

Guide:How to do BMW ICOM NEXT DHCP Configuration + WiFi Connection

Tool: ICOM Next
Car: BMW F10 series
BMW ICOM NEXT

DHCPI have configured this to work before with a chinese clone but ISTA+ wont connect with ICOM Next. Configured ICOM to DHCP, did the same to TP-Link router. Submask for LAN the same for ICOM and router. I get identification error. If I remove router, connection is OK except for ICOM Direct interface option in ISTA. I followed the numerous DHCP configuration instructions found around the internet.

WIFI OptionIt is quite frustrating finding info from the forums. All posters assume everyone is at the knowledge level they are at. I have Icom next genuine and TP-Link router. I tried setting up WLAN and my icom came up with “UNSUPPORT service” in itoolradar and green light in WLAN when ethernet disconnected. However my ethernet was then failing to connect so restored the ICOM. Got me really worried.Well, searched a lot on the web..

And almost solved!!!
Managed to set up the WIFI. You set up TP-Link as an access point, access key similar to that in ICOM,access point name common to both router and ICOM configuration. Then connect TP-Link to ICOM with ethernet cable, in wifi, connect to the WIFI network you just set up. I can now receive IP address in itoolradar as if it was in DHCP mode.
BUT IT CANT CONNECT TO CAR. IDENTIFICATION FAILURE. Tried all interface options. Needless to ask, interface set up with Easy connect. I can see icom interface in connection manager, KL15 has voltage, I have ethernet and Dcan shown as available protocols in connection Manager but still no luck. Direct connection with ethernet works a treat. Where is the quirk in DHCP or WIFI connection?

Well, I can now work wirelessly with any ICOM!!!
My connection issue was VMware adapter. Disabled it and now I can connect by plugging in the TP-Link router to ICOM and setting it up as an access point. ICOM in DHCP, laptop in DHCP. Perfecto!!
Only method that I cant get to work is pure WIFI i.e ICOM to car, Wifi router as accesspoint on power, laptop connected to access point wifi. I don’t get any IP on itoolradar this way. BMW ICOM may not be connecting to the router but honestly, I don’t care since my set up works I,e router connected to icom via ethernet
Tried Mypublic wifi software but it does not run on my win 10, No idea why, It just does not set up.

No Comments in Mb Star

Solutions for SD Connect 4 DAS License Key is Corrupted

I have bought SD Connect 4 , when i use it get the message as bellow :

Your license key is corrupted

please contact support@…

How to solve this issues ? I get help from the seller : sale@cnautotool.com

 

The DAS need activation

Xentry/DAS activation steps :

Step 1: Run StartKeyCenter to get ID for activation

Open “StartKeyCenter” on Desktop, to get the SD connect c4 Hardware ID and App ID

Complete Licence information (Hardware ID, App ID, StartDay, ExpirationDay), then click “Generate” to get License String

Copy License String, then go to “StartKeys”, click “Enter” to read StartKey, then “Save” data

Step 2: Reactivate Xentry/DAS

Go to Local Disk C:/ ProgramData/ LicDir, the copy and paste “lic_key_2.dat”, re-name as “lic-key_2.x4711”

Setup Properties of “lic-key_2.x4711”, select Read-only

Then open XENTRY Diagnostics Openshell and close it

The issues solved now

(NOTE: this avoids the activation code to be lost and reactivate XENTRY)

No Comments in OBDSTAR

Newest Update for OBDSTAR X300 DP PLUS PAD2

OBDSTAR X300 DP PLUS is a new Android-based vehicle trouble diagnostic device developed for internet applications. It inherits from OBDSTAR advanced diagnosing technology and it is characterized by covering wide range of vehicles, featuring powerful function, and providing precise result. Through vehicle diagnostic OBD connector and variant mobile intelligent terminals, it achieves vehicle trouble diagnosis for full car model and full system vehicle.

 

Update on June,2019 of OBDSTAR X300 DP.

1.IMMO

VW

Optimized the key learning function

 

Nissan

  1. Increased 12-digit Pincode smart key system type3
  2. Increased 12-digit Pincode IMMO system type3

 

BAIC

  1. Optimized Senova D50 key programming
  2. Optimized Hyosow S6 smart key programming procedure
  3. Increased BAIC new energy EU5 smart key system group 2 Initialization enter into system scanning mode

 

Ford

  1. Optimized Courier(Tourneo Courier) key programming
  2. Optimized Ecosport Pincode algorithm in key programming
  3. Optimized Kuga Pincode algorithm in smart key programming

 

Chrysler

1.New Increased:300/300C(2015-2017/2018-),300(2019),PACIFICA(2018/ 2019),VIPER(2015-2017),CHALLENGER(2015-2017/2018/2019),RAM(2018)

CHARGER(2015-2017/2018/2019),DURANGO(2014/2018-2019),WRANGLER(2018-2019)

  1. Increased 2017- Renegade smart key system
  2. Increased 2017-2018 Compass smart key system
  3. Increased 2018-2019 Grand Cherokee smart key system
  4. Optimized 300C(2005-2006)(2015-2017) function menu
  5. Optimized US-Canada area 2014-2015 Grand Cherokee key programming
  6. Optimized US-Canada area 2015-2016 Renegade key programming
  7. Optimized US-Canada area 2008 Grand Cherokee key programming
  8. Optimized US-Canada area 1998-2000 300M key programming security algorithm

 

Mazda

  1. Increased 2017- CX9 smart key programming
  2. Optimized 2018 CX4 smart key system ignition on function
  3. Optimized 2018 CX4 smart key system all keys lost programming procedure

 

Renault/Dacia/Lada

  1. Optimized Megane
  2. Optimized 2012 Fluqnce flipkey
  3. Optimized 2015 Dacia Logan key programming

 

Great Wall

  1. Increased data index ID
  2. Solved Haval H6 2017- smart key programming failure

 

Fiat

1.Increased Ferrari 612 Scaglietti and California

2.Optimized 2016- Maserati smart key IMMO data reading

3.Optimized BSI_MARELLI_70F3633_95320 type EEprom reading

4.Revised Iveco key programming type LIER_BCM and DELHP_IMMO prompt text

 

Venucia

Increased and optimized D60 smart key system

 

Foton

  1. Optimized Tunland remote system
  2. Increased the help data ID

 

Geely/SMA/Englon

Optimized Emgrand EV450 UMC smart key system

 

GM

  1. Solved Excelle 2018- prompt 7F E3 problem
  2. Solved GL6 2017- security verification failure

 

JMC

Increased the data ID

 

Honda/Acura

Increased the data ID

 

Luxgen

Increased the data ID

 

Roewe/MG

  1. Increased the data ID
  2. Increased Roewe E50 IMMO system
  3. Increased Roewe RX8 IMMO system
  4. Increased Roewe Ei5 IMMO system
  5. Increased MG GS smart key system
  6. Increased MG MG6 smart key system
  7.  Increased MG ZS smart key system
  8. Increased Roewe 750 (new) IMMO system
  9. Optimized Roewe RX3 IMMO system (non-smart)

 

 

2.Cluster Calibration

Ford

  1. Revised FOCUS 2018- to be FOCUS 2019
  2. Optimized 2017- Ecosport cluster calibration procedure
  3. Increased 2017- EcoSport/2017- Carnival/2018- Focus/2018- Transit Custom

 

Great Wall

Increased Hover H6 and H8 cluster calibration function

 

Mercedes-Benz

Optimized Benz B series W245 cluster calibration function

 

Peugeot/Citroen

  1. Shielded the Citroen C5 menu
  2. Increased the model‘help’ index
  3. Shielded Citroen BSI_P0X extra function menu(recover FLASH)

 

VW/Audi/Seat/Skoda

Updated the function of automatically recognize the dashboard type

 

Kia/Hyundai

Optimized the algorithm file of encrypted chip

 

 

3.APK Software

Increased Java Script in Help section, support the online automatic multi-language translation

 

 

Update on July 2019 OBDSTAR X300 PAD

1.IMMO

BISU

  1. Updated the car logo and increased the data ID
  2. Optimized T3 smart key system key programming3. Optimized T5 smart key system key programming and procedure
  3. Optimized M3 smart key system key programming and procedure

 

Changhe

Increased Help data index

 

Changan

Increased CS85 smart key system

 

GM

  1. Increased the model index ID
  2. Optimized Cadillac XTS communication time

 

Fiat

  1. Optimized data index
  2. Updated the car logo
  3. Optimized 93C86(ENCRY) type 3
  4. Optimized 1K79X(48) and 3K91D(48) type pre-coding function

 

Maserati

  1. Increased the Maserati multi-language help data
  2. Increased 2016- Maserati smart key programming and Pincode reading (FCA connector needed)

 

Renault

  1. Increased 2018- Symbol key programming
  2. Increased Fluence blade key programming
  3. Increased 2016- Clio IV key programming (Add key)
  4. Increased 2015- Capture key programming(Add key)
  5. Optimized Master key programming
  6. Optimized 2017 Symbol key programming
  7. Optimized 2015 Fluence blade key programming
  8. Increased 2016 Clio 4 new type (new Flash version)

9.Increased 2011 Latitude new type key programming (automatic recognition)

 

Mazda

  1. Increased index ID
  2. Increased DEMIO 2017- smart key system
  3. Increased Mazda 2 2017- smart key system
  4. Optimized 2018 models smart key programming procedure

 

Chery

Optimized the smart key system menu

 

Land Rover

Optimized 2014- smart key system programming

 

Nissan

Increased Kicks smart key system

 

SWM

  1. Optimized G01 smart key system
  2. Optimized X7 smart key programming

 

JAC

  1. Increased data ID
  2. Increased Sunray IMMO system
  3. Increased Sunray Delphi IMMO system
  4. Increased Sunray DIAS IMMO system

 

Hyundai

  1. Increased the Help index ID
  2. Optimized Elantra 2008-2011 IMMO system

 

Jaguar

  1. Optimized the menu
  2. Increased the Help index ID
  3. Optimized 2013- smart key system

 

Traum

Optimized S70 BCM

 

Kia

Increased the ‘Help’ index ID

 

Changan

  1. Updated the car logo
  2. Increased CS15 EV electric BCM
  3. Optimized CS85 smart key system
  4. Increased Aoshan EV remote system
  5. Increased Xingka EV remote system
  6. Increased CS75 PHEV smart key system
  7. Increased Ruixing S50T remote system
  8. Increased A600 BCM and smart key system
  9. Increased CS35PLUS integrated BCM and Delphi BCM
  10. Increased Eado PHEV BCM and smart key system
  11. Increased Aoshan X70A BCM and smart key system
  12. Increased Niou II smart key system and remote system
  13. Increased Cosmos smart key system and remote system
  14. Increased Eado DT integrated BCM and smart key system
  15. Increased RAETON CC integrated BCM (remote) and Delphi BCM (smart key)

 

Opel

  1. Increased VAUXHALL MORANO 2014- smart key system
  2. Increased Astra-G Y17DT/Y17DIT Pincode reading from ECM system
  3. Increased Corsa-C Z10XEP/Z13DTJ Pincode reading from ECM system
  4. Increased Corsa-D Z10XEP/Z12XEP/Z14XEP/Z16LER Pincode reading from ECM system
  5. Increased Zafira-B Z16XE1/Z16XEP/Z20LEH/Z20LER Pincode reading from ECM system
  6. Increased Astra-H Z12XEP/Z14XEP/Z14XEL/Z16XEP/ Z17DTH/ Z17DTL Pincode reading from ECM system                                                               

 

Peugeot/Citroen/DS

Increased the ‘Help’ index ID

 

Lifan

Optimized 720 remote system

 

Ford

  1. Increased Escort 2017-2018 All Blade Keys Lost
  2. Increased New Mondeo 2017- All Smart Keys Lost
  3. Increased Everest 2017- All Blade Keys Lost
  4. Increased Everest 2017- All Smart Keys Lost
  5. Increased Transit 2018- All Blade Keys Lost
  6. Increased Edge 2017- All Smart Keys Lost
  7. Increased Explorer 2017- All Smart Keys Lost
  8. Increased Mustang 2017- All Smart Keys Lost
  9. Increased Fusion 2018- All Smart Keys Lost
  10. Increased GALAXY 2015- All Smart Keys Lost
  11. Increased RANGER 2019- All Smart Keys Lost
  12. Increased FIGO/FIGO ASPIRE 2017- All Blade Keys Lost
  13. Increased F-150 2017- All Smart Keys Lost
  14. Increased F-250 2017- All Smart Keys Lost
  15. Increased F-350 2017- All Smart Keys Lost

 

Lincoln

  1. Continental 2017- All Smart Keys Lost
  2. NAUTILUS 2018- All Smart Keys Lost
  3. NAVIGATER 2018- All Smart Keys Lost
  4. MKC 2017-/MKZ 2017-/MKX 2017- All Smart Keys Lost

 

Chrysler

  1. Optimized the menu
  2. Increased all models data ID
  3. Optimized 2014-CHEROKEE key programming

 

BMW

Updated the index ID

 

JMC

  1. Updated the car logo
  2. Optimized Yusheng 350/330smart key system

 

SsangYong

  1. Increased Korando diesel 2.0T/2.2T key programming
  2. Increased New Korando gasoline/diesel key programming
  3. Increased Actyon diesel 2.0T/2.2T key programming
  4. Increased Stavic Rodus diesel 2.0T/2.2T key programming
  5. Increased Rodius diesel and gasoline key programming
  6. Increased Rodius diesel 2.0T/2.2T key programming
  7. Increased Rexton diesel 2.0T/2.2T key programming
  8. Increased Tivolan gasoline and diesel key programming
  9. Increased remote programming type 2
  10. Increased data ID

 

Haima

  1. Updated the car logo
  2. Increased S5 youth edition Xiamen TTE BCM (CAN)

 

Zotye

  1. Optimized T700 key adding function
  2. Optimized SR7 remote programming procedure

 

Venucia

  1. Updated the car logo
  2. Optimized ROOT menu
  3. Optimized T70/T90 smart key system

 

BYD

Updated the car logo

 

VW

  1. Updated the car logo
  2. Increased the smart mode

 

 

2.Cluster Calibration

KIA/Hyundai

  1. Increased data index ID and updated the car logo
  2. Optimized KIA K5 D70F3423 cluster calibration

 

Mercedes-Benz

Increased model index ID

 

Peugeot/Citroen

  1. Optimized the menu
  2. Increased the ‘Help’ index ID
  3. Optimized 508 cluster calibration

 

Maserati

  1. Increased index ID
  2. Optimized cluster calibration function
  3. Increased GHIBLI-95320 cluster calibration

 

Chrysler

  1. Increased the model index ID
  2. Increased Charger 2019 cluster calibration
  3. Increased Cherokee 2019 cluster calibration

 

Jaguar

Optimized XJ-2016 cluster calibration

 

Iveco

  1. Increased 2007- cluster calibration
  2. Increased 2011- cluster calibration
  3. Increased 2014- cluster calibration
  4. Increased data index ID

 

Renault

  1. Increased model data index ID
  2. Twingo III cluster calibration
  3. Trafic IV 2013- Block ABS/Unlock DASH cluster calibration
  4. Captur 2017- Block ABS/2017- Unlock DASH cluster calibration
  5. Captur 2013- Block ABS/2013- Unlock DASH cluster calibration
  6. Clio IV 2017- Block ABS/2017- Unlock DASH cluster calibration
  7. Clio IV 2013- Block ABS/2013- Unlock DASH cluster calibration
  8. Trafic IV 2017- Block ABS/2017- Unlock DASH cluster calibration

 

Kia/Hyundai

Optimized ICM_MB91F06XBS type communication

 

Mitsubishi

  1. Increased ASX 70F35XX cluster calibration
  2. Increased L200 2017-(MONO) cluster calibration
  3. Increased ASX MB91F223+93C86 cluster calibration
  4. Increased OUTLANDER III 70F3425 COLOR cluster calibration
  5. Increased OUTLANDER III 70F3425 MONO cluster calibration
  6. Increased OUTLANDER MB91F223+93C86 cluster calibration
  7. Increased OUTLANDER SPORT 70F35XX cluster calibration
  8. Increased model index ID

 

Great Wall

Optimized Hover H6 security verification procedure

 

Ford

  1. Increased the model index ID
  2. Optimized Escape 2013 cluster calibration
  3. Optimized Focus 2007 models cluster calibration

 

Peugeot/Citroen

Revised BSI_N0X cluster calibration prompt

 

VW/Audi/Seat/Skoda

Optimized 2005 Caddy and 2006 Sagitar cluster calibration

 

Nissan            

  1. Increased the ‘Help’ data index ID
  2. Increased Kicks 2016- Block ABS cluster calibration
  3. Increased Kicks 2017- Block ABS cluster calibration
  4. Increased Kicks 2017- Unlock DASH cluster calibration
  5. Increased Kicks 2016- Unlock DASH cluster calibration
  6. Updated the icon

 

Porsche

  1. Increased the model index ID
  2. Optimized Panamera and Cayenne 2010- cluster calibration procedure

 

Toyota

  1. Updated the icon
  2. Optimized Camry 2018 cluster calibration procedure

 

Volvo

  1. Increased index ID
  2. Updated the car logo

 

VW/Audi/Seat/Akoda

  1. Updated the car logo
  2. Optimized 2012- A6L EEPROM reading

 

 

3.ECU Clone

GM

  1. Increased the model index ID
  2. Increased 2017- GM ECU clone algorithm

 

 

 

 

 

 

 

 

No Comments in OBDSTAR

OBDSTAR X300 DP Plus support 2016 Ford F150 Key programming

This instruction show you guide on how to use OBDSTAR X300 DP Plus to program key for Ford F150 2016.
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-1

Procedures:
Connect OBDSTAR Key Master Plus(X300 DP Plus) to Ford F150 obd port
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-2
Select “Diag Program”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-3

Select “IMMOBILISER” and select “Ford/LINCOLN”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-4

Select “Ford/LINCOLN V32.43” and click “Enter” to continue
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-5

Select “Ford” and click “Enter”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-6

Select “Immobiliser” and click “Enter”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-7
Select “F150/F250”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-8

Select “2015-2019”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-9

Select “Key Number” and click “Enter”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-10

Make sure there are at least 2 keys
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-11

Insert a working key into ignition and turn on the light the dashborad
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-12
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-13

Press “Enter” to continue
And make sure WIFI is connected,then click “Enter”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-14

Wait for reading data
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-15
Configuring the system,please wait…
Then insert a new key and switch ignition on,click “Enter”
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-16

Key program success.
OBDSTAR-X300-DP-Plus-support-2016-Ford-F150-Key-programming-17

FREE License Key for Caterpillar ET (Electronic Technician) Software

1. First Step, install Caterpillar ET Software: ET_2010A_v1.0, wait until Status is complete.

FREE-License-Key-for-Caterpillar-ET-(Electronic-Technician)-Software-1

2. Second Step, Open Caterpillar ET through shortcut on Desktop or Start Menu/ All Program, double click on Electronic Technician.
After Software opened, will showing a Message Box as below;

FREE-License-Key-for-Caterpillar-ET-(Electronic-Technician)-Software-2

NOTE: Software is Not Licensed, then Click YES..

FREE-License-Key-for-Caterpillar-ET-(Electronic-Technician)-Software-3

Yap, I have Software to Generate License Key, Full Service Dealer ET

FREE-License-Key-for-Caterpillar-ET-(Electronic-Technician)-Software-4

Please comment your License Code, I will give you License Key to activate your Electronic Technician Software.

No Comments in Autel Tools

Autel MaxiIM IM608 VS MaxiIM IM508 VS Auro OtoSys IM600 VS IM100

Autel factory combine Cnautotool.com engineer make a comparison table about Autel MaxiIM IM608 VS Autel MaxiIM IM508 VS Auro OtoSys IM600 VS Auro OtoSys IM100.

They can compare with each other in the aspects of IMMO (key programming, key learning, pin code read etc.), programming, OE-Level diagnosis, Advanced Service Functions, configurations etc.

Product Autel MaxiIM IM508 Autel MaxiIM IM608 Auro OtoSys IM100 Auro OtoSys IM600
Image  Autel-MaxiIM-IM508  Autel-MaxiIM-IM608  AuroOtoSys-IM100  AuroOtoSys-IM600
IMMO
Smart Mode (Guided and Automated Key Learning Function)
Expert Mode (Advanced key Learning)
Auto Detect Make/Model/Year/System
Read PIN/CS
Read PIN/CS (All Keys Lost)
Key Generation
Key Learning
IMMO ECU Reset/Adaption
IMMO ECU Refresh/Coding
Remote Learning
Backup /Restore IMMO Data
AUDI Q5/A4/A5 2015-2017 Read PIN/CS N/A
BMW FEM/BDC Key Learning and Adaption
Mercedes Key Learning ×
Benz 3rd Generation IMMO Add key, all key lost, key Learning N/A
BMW FEM/BDC Key Learning and ECU adaptation
BMW CAS4/3/2 key learning CAS4 available when connected to XP400
VW /Audi MQB (VDO & JCI) add key, IMMO V A4/A5/Q5 2015+ Key learning N/A
VW /Audi /Skoda / Seat IMMO III /IV /V add key, all key lost
Programming
Key read /write
EEPROM Read/Write
MCU Read/Write Basic Advanced Basic Advanced
ECU Read/Write When connected to XP400
MC9S12 Encryption Chip read/write When connected to XP400
IC Card Read/Write When connected to XP400 N/A
Mercedes Infrared Key Read/Write When connected to XP400 N/A
Remote Frequency Detect When connected to XP400 N/A
Support PC When connected to XP400
OE-Level Diagnostics
All Systems for Over 80 Makes and Models N/A
AutoVIN /Auto scan
Read /Erase codes
View, record, playback live data
View Freeze Frame data
Shop and data Manager applications
MaxiFlash JVCI ECU Reprogrammer (Bluetooth /USB cable) N/A
OtoFlash (J2534 ECU Reprogrammer) N/A
Advanced Service Functions
Oil Serive Reset
Parking Brake Pad Relearn After Replacement
Steering Angle Sensor Relearn
Battery Registration and Reset
Diesel Particulate Filter Regeneration
Tire Pressure Monitoring System Sensor ID Relearn
ECU Coding N/A N/A
VW/Audi Component Protection N/A
Complete Service Functions N/A N/A
Tool Features
Built-in Rechargeable Li-ion Battery 5000 mAh 15000 mAh 5000 mAh 15000 mAh
Internet Updatable Wi-Fi Wi-Fi Wi-Fi Wi-Fi
Multilingual Support
One Year Warranty
Free Online Update Two Years
Touchscreen 7-inch 10.1-inch 7-inch 10.1-inch
Memory 32 GB 64 GB 32 GB 64 GB
Processor Cortex-A9 processor Cortex A7+A15 six-core processor Quad-core processor Hexa-core processor
Camera N/A 8.0 Megapixel N/A 8.0 Megapixel
Resolution 1024×600 1920×1200 1024×600 1920×1200
Note: XP400 can be purchased separately. 
Some listed functions are manufacture dependent. Constantly update MaxiIM for current vehicle coverage. Update software regularly for most accurate tool features. 
No Comments in Xhorse

VVDI Key Tool from 2.3.5 firmware is GL version(Global) for customers

One user’s Feedback: Just heads up – do not upgrade Key Tool!!
I confirmed from few sources – they already stopped manufacturing of original Key Tool. I was stupid enough to upgrade to version 3.2.5. Originally tool was NA (North American) firmware, but with 3.2.5 firmware became GLOBAL. Some remotes are missing now (not on the list, and not in the XHORSE app either, so Mini Key tool is useless, I have it too). So if you’re happy with what you have – do not upgrade above version 3.2.2 or even lower! There’s no option to downgrade back to local (for example, North American) version – confirmed with some sales rep in China. “i am sorry that the GL version cannot be back. i confirmed with engineer” – was reply.
Very disappointed.
Until now it was best tool to use, new mini key tool just stupid toy with SOME features of Original Key Tool.

Mini-Key-tool

Official Xhorse Claim:
VVDI Key Tool GL version still updating but if you need NA version, i can setting for you. PM me your device SN.
About GL version explanation
From different regions customer’s feedback, they also need some other regions remote options(like ME region they also need some SE and EU database options)
So from 2.3.5 firmware there is GL version(Global) for customers.
1GL version from old 3 regions include(EU ME SE), those 3 old regions will automatically change to GL version from 2.3.5 firmware.
2GL version will cover more remote options, will keep updating and adding more remotes (if you find any options missing compare to old region version, you can PM to uobdii.com, the Xhorse will update)
3GL version already released universal smart key generation options.
4If customer still prefer to keep old region version, just PM cnautotool.com about your device SN, Xhorse will setting back for you.(GL or keep old region version).
Or you can directly contact at Samic.

No Comments in Autel Tools

How To Register Autel MaxiDiag MD808/MD808 Pro?

As we all know , all autel scanners need to register first , then you could download software, update online, retrieve information and get warranty service . We have customers who dont know how to register autel MaxiDiag MD808 ( or MD808 Pro ) , please check all details as bellow :

Notice : Before registration , please confirm your network is working properly .

Registration Steps :

1. Visit the website http://pro.autel.com.

2. If you already have an Autel account, Sign In with your account ID and password.

3. If you are a new member to Autel, click on the Create Autel ID button on the left side to create an ID.

4. Enter the required information in the input fields, and click the Get Verification Code button to get a verification code for email validation.

5. The online system will automatically send a verification code to the registered email address. Input the code in the Verification Code field and complete other required fields. Read through Autels Terms and Conditions and click on Agree, and then click Create Autel ID at the bottom. A product registration screen will display.

6. The devices serial number and password is located in the About section of the System Setup application on the tool.

7. Select your product model, enter the product serial number and password on the Product Registration screen, and click Submit to complete the registration procedure.

After registration finished , you can use your tool now .

Any more help , welcome to contact us directly : sale@cnautotool.com

www.cnautotool.com